Search Icon
MOBATIME Homepage Breadcrumb chevron icon ProductsBreadcrumb chevron iconPTP IEEE-1588 SystemsBreadcrumb chevron iconPTP GrandmasterBreadcrumb chevron iconDTS 4160.grandmaster i

IEEE-1588 PTP Grandmaster - DTS 4160 i

Mobatime dts4160-1 NTP PTP time server IEEE-1588 grandmaster DCF E1 SyncE pulse frequency phase synchronization IRIG front view
Mobatime dts4160-1 NTP PTP time server IEEE-1588 grandmaster DCF E1 SyncE pulse frequency phase synchronization IRIG front view Mobatime dts4160-3 NTP PTP time server IEEE-1588 grandmaster DCF E1 SyncE pulse frequency phase synchronization IRIG DTS 4160i back view, PTP, NTP, time server, grandmaster Mobatime dts4160-4 NTP TPTP time server IEEE-1588 grandmaster DCF E1 SyncE pulse frequency phase synchronization DTS 4160i, detail, PTP, NTP time server, grandmaster

IEEE-1588 PTP Grandmaster - DTS 4160 i

DTS 4160 i is a combined
time distribution and synchronization
device with up to 4 network ports
(IPv4/IPv6). With its high-precision and
intelligent concept for redundant operation,
it offers a high degree of reliability
and availability.

Get an offer Learn more
Oscillator type:DTS 4160a.grandmaster i / Type A with OCXO Oscillator | DTS 4160c.grandmaster i / Type C with Rubidium Oscillator
4 completely separated LAN ports (3x RJ45, 1x SFP):provides PTP on 3 ports 1- and 2-step master or slave, different profiles and domains per port, multicast/unicast, IPv4/IPv6/Layer 2, provides NTP on 4 ports (<10'000 requests/s on all 4 ports combined)
Outputs:4x E1 BNC (unbalanced), 2x pulse/frequency/10MHz outputs, 1x IRIG-B / AFNOR, 2x serial output, 1x DCF current loop output
High precision time:Time reception from GPS, GLONASS or Beidou, GPS disciplined oscillator (GPSDO)
Redundancy:master-slave operation with automatic switch over in case of an error
Show more
IP configDHCP, DHCPv6, static IP, Autoconfiguration
Power supplySupply 1 (standard mains connector for 240VAC), Supplies 2 & 3: 22..29 VDC
AccuracyGPS to internal time: typ. < +/- 30ns, Redundant link to internal time: typ. < +/- 50ns, PTP to internal time: yp. < +/- 50-100ns, DCF to internal time: typ. < +/- 200ns (after compensating fix offset)
OperationMOBA-NMS, Telnet, SSH, SNMP (V2c/V3 get, put), RS 232 (terminal)
Show more

Both, PTP and NTP provides time synchronization over a packet based network. But not both protocols are dedicated to the same application fields. It depends on the system’s needs, which of the protocol is preferred.

PTP is needed where a higher level of precision is required (e.g. Telecom, Power distribution, Air traffic control etc.) With PTP sub microsecond or even nanosecond accuracies are feasible, whereas NTP only reaches millisecond level. The key of PTP is hardware timestamping. Only if the timestamping happens close to the wire, it is possible to reach this high level of accuracy. The drawback of it is the need for dedicated hardware and an engineered network.

NTP is an old Internet protocol which is still widely used to distribute time (e.g. clock systems or IT Networks). NTP provides a simple way to synchronize all device over a regular network and even over internet. To ensure a reliable time in a local network, the best solution is to place an NTP server, which is connected to a GNSS Antenna, into the network. Whereas time is needed for clocks, access control systems and other such systems the accuracy of NTP is sufficient. The benefit of NTP is it’s robustness and it’s ability to run on a standard IT equipment.

If you need further information on this topic, please do not hesitate to contact us. We would be pleased to support you.

PTP is the “Precision Time Protocol”, which is defined in IEEE 1588. In contrast to NTP, this is a network protocol, which is characterized by significantly higher accuracies (down to the nanosecond range) and is usually used in locally limited networks (e.g. measurement / control / regulation technology, automation technology, etc.).

 

In the foreground is not the absolutely correct time information, but rather the high-precision “clocking” of interconnected devices in such industrial or computer networks. In connection with the PTP network organization and clock types, one speaks initially of Grandmaster Clocks (best possible reference device) and Boundary Clocks (devices with master and slave function), whose role distribution is determined using the best Master Clock algorithm. On the other hand, clearly defined roles are assigned to the ordinary clocks (either as master or clients), so-called transparent clocks then only forward the PTP time stamp when corrected. The runtime correction is ensured using complex computing algorithms. So it is not the case that one procedure is to be replaced by the other: NTP and PTP have different functional focuses, which is why both will continue to have authorization in the future and can also be used in parallel in computer networks if necessary.